Nova-Strobe DBLandNova-Strobe PBLDeluxe and Phaser LED StroboscopesMONARCH INSTRUMENT Instruction Manual15 Columbia DriveAmherst, NH 03031 USAPh
62.2 Input / Output ConnectionsThe strobe has input and output jacks on the left side of the stroboscope. These can be used for external triggering o
7The polarity of the input pulse can be set in the MENU options. In the external mode the knob cannot be used to change the fl ash rate.With no externa
8button. Note: The system will round the display to the nearest least signifi cant digit displayed. If the display has no decimal places and you enter
93.1.5 Fixed Increment N AdjustmentThe strobe fl ash rate can be incremented or decremented in fi xed increments. To do this, adjust the fl ash rate to
10the preset number of degrees provided this does not exceed the strobe specifi cations. Press any key other than BRIGHT to exit or press BRIGHT again
11the display. There is also an ON TARGET INDICATOR shown right which illuminates when a valid external signal is received.If there is no external inp
123.7 Phase DelayThe DELAY button adjusts the phase shift of the fl ash with respect to time. There are two modes: INTERNAL and EXTERNAL (PBL
13In the External Time Delay mode the fl ash is delayed 0.01 to 1000 msec after each external trigger pulse. The display will show the TIME icon, th
143.8.2 BacklightEnables the display backlight to be turned on or off. After pressing the MENU button rotate the knob until the display bottom line
153.8.5 BlankingBlanking is used to reject the strobe’s own fl ash when using an external optical sensor and prevent double triggering. After pressing
Safeguards and Precautions1. Read and follow all instructions in this manual carefully, and retain this manual for future reference.2. Do not use th
16button. You should again see a single image (which may be phase shifted with respect to the fi rst image seen).For example, when viewing a shaft with
17If a Remote Optical Sensor or Magnetic Sensor is used to sense one pulse per revolution (External mode), the readout will display directly in RPM (F
185.1 Low Battery IndicationWhen the batteries are charged, there will be no battery icon indication. When the batteries are low, the Low Battery ic
19Allow the recharger to charge the batteries until the display shows DONE for peak battery life performance. If the batteries are not
206.0 SPECIFICATIONSInternal Mode:Flash Range 30 - 500,000 FPM (Flashes Per Minute), 0.5 to 8333.33 HzFlash Rate Accuracy 0.004% of setting
21Memory Last setting before power down is remembered and restored on next power up. 5 user settable fl ash rates.Input Power Battery powered: Inte
7.0 OPTIONS AND ACCESSORIES / SENSORSPSC-2U Universal Recharger, 115/230 Vac with USA, U.K., AUS, Euro Adapter Plugs for battery operated Nova-Strob
ROS-P-25 Remote Optical Sensor with 25 foot [7.6 m] cable for triggering strobeIRS-P Infrared Sensor with 8 foot [2.5 m] cable for
Printed in the U.S.A. Copyright 2013 Monarch Instrument, all rights reserved1071-4231-111R-0513
TABLE OF CONTENTSTABLE OF CONTENTS1.0 OVERVIEW ...11.1 Modes of Operation
3.0 LED STROBE OPERATION ...73.1 Adjusting the Flash Rate - RPM ...
1Figure 1 LED Strobe Control Panel1.0 OVERVIEW The Nova-Strobe Deluxe DBL and Phaser PBL LED (Light Emitting Diode) are rugged po
21.1.1 Internal ModeThe strobe is in the Internal Mode when nothing is plugged into the input jack or when manually set using the INPUT button. In th
31.2 BrightnessGLOSSARY: LED – Light Emitting Diode msec – millisecond = 1/1,000 of a second µsec – microsecond = 1/1,000,000 of a second ° = deg
4to take into account tangential velocity (rotational speed) – the further away the rotating point is from the center axis the faster the tangential v
5The strobe automatically adjusts these values as the fl ash rate is increased or decreased to maintain these limits at all times. For example - at
Kommentare zu diesen Handbüchern